Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
How do you really feel in relation to How to Install a Bathtub?
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is conveniently easily accessible, the task can move speedily; if you need to open a wall to get rid of the old tub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a brand-new tub as well as do not need to alter the plan of your previous water pipes.
Your devices and also material checklist must make up the following:
Planning for the Installment
To start with, the supporting framework supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of eliminating the existing faucets can be rather troublesome because of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the bath tub has been utilized at least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the tap in position with the producer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, resulting in problems with wetness and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about Installing A Bathtub while looking around the web. Sharing is good. Who knows, you may very well be doing someone a favor. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Hire A Pro
Report this page